[Guide] Homebrew powered risers.
-
[s]nutnut, will you update your guide with how to add eathing to the risers?[/s]
edit:
So after my serious brain fart and meltdown, I figured out the right sentence structure;
Nutnut, will you be updating your guide with how to add grounding to the home-made risers? -
I’ve order some ‘normal’ risers so i am going to read this topic carefully soon!
Added the guide to:
[url=http://forum.feathercoin.com/index.php/topic,685]http://forum.feathercoin.com/index.php/topic,685[/url] -
Any chance this could be compressed into one page, I’ll edit into the pinned guide in mining, if required?
I found it confusing what was decided safe at the end. Possibly room for someone to do a Youtube / Blue Peter “video how to”.
I just use a riser, but I like to see steam punk solutions.
-
Anyone has any objections to the following -
Ideal riser should be
0*) PCIEx16 -> PCIEx1, cause mining does not require bandwidth and x1 link theoretically puts lower strain on the mg chipset/CPU.
Tho some motherboards will require presence shorting if x1 risers are used in x16 slots.-
“cut” - to prevent current flow from/to motherboard voltage regulatorsPSU and to enable use of multiple PSUs
-
have thick enough wires on +12v lines, so they won’t burn, but not thick enough to cause significant voltage drop
-
all +12v lines shorted on the riser - to not overcurrent one pin only
-
wires soldered directly to slot
5*) +5v/+3v lines also going to PSU --> “ideally”
-
capacitors on +12vground, closer to load - better, HF fast capacitors, tantalum(?), solid(?), rating(?)
-
ground line also soldered and connected to PSU
Ideal multi-PSU
- different PSUs +12v rails separated from each other
- different PSUs +5/+3 rails separated from each other
3*) same PSU rails not mixing with each other - Properly synced - aka turning on/off at the same time
* does not really matter or not in the scope of the subject
-
-
[quote]6) capacitors on +12vground, closer to load - better, HF fast capacitors, tantalum(?), solid(?), rating(?)[/quote]
As for solid electrolytes, you want some radial ones probably. Nippon Chemi-Con PSC 270uF/16V (diameter 8mm) are a good choice. PSA or PS are older models with a little bit higher ESR. If you can get and fit Nippon PSC 470uF/16V (diameter 10mm), that’s even better. Sanyo solid electrolytes are more expensive usually unless you’re salvaging them from broken equipment.
-
[quote name=“ghostlander” post=“47275” timestamp=“1387875839”]
[quote]6) capacitors on +12vground, closer to load - better, HF fast capacitors, tantalum(?), solid(?), rating(?)[/quote]As for solid electrolytes, you want some radial ones probably. Nippon Chemi-Con PSC 270uF/16V (diameter 8mm) are a good choice. PSA or PS are older models with a little bit higher ESR. If you can get and fit Nippon PSC 470uF/16V (diameter 10mm), that’s even better. Sanyo solid electrolytes are more expensive usually unless you’re salvaging them from broken equipment.
[/quote]Thanks, I have a batch of Sanyo OS-CON, will use them.
-
[quote name=“wrapper0feather” post=“45855” timestamp=“1387380800”]
Any chance this could be compressed into one page, I’ll edit into the pinned guide in mining, if required?I found it confusing what was decided safe at the end. Possibly room for someone to do a Youtube / Blue Peter “video how to”.
I just use a riser, but I like to see steam punk solutions.
[/quote]
+1
Do this, this, this, end.
No opinions :) -
[url=http://www.kitguru.net/components/power-supplies/zardon/silverstone-strider-gold-1200w-psu-review-sst-st1200-g/2/]http://www.kitguru.net/components/power-supplies/zardon/silverstone-strider-gold-1200w-psu-review-sst-st1200-g/2/[/url]
[img]http://www.kitguru.net/wp-content/uploads/2011/06/cables.png[/img] -
nutnut, rep for the post as it saved me a bunch of$$ on risers and I believe will end me with a better quality rig.
Suggestion for the next info post would be wiring of dual PS on a 4 card rig.
Thanks again
~//~ -
I’m curious do I still need to cut the cables to remove it from going back to the board. Because I plan on being able to have 7 AMD R9 280x GPU’s in one rig. 5 x PCI-E X16 powered riser and 2 x PCI-E X1 --> PCI-E X16 powered riser
Basically they are these ones [url=http://www.moddiy.com/products/PCI%252dExpress-PCI%252dE-1X-to-16X-Riser-Ribbon-Extender-Cable-w%7B47%7DMolex-%252b-Solid-Capacitor-%2830cm%29.html]http://www.moddiy.com/products/PCI%252dExpress-PCI%252dE-1X-to-16X-Riser-Ribbon-Extender-Cable-w{47}Molex-%252b-Solid-Capacitor-(30cm).html[/url] and their PCI-E X16 --> PCI-E X16 equivalent as well… Do I need to do any modifications to keep it from frying my board or no?
Also I have planned on two Silverstone Zeus 1,350 Watt PSUs for my rig how should I connect them all? Can I use one PSU for say the motherboard, HD, and such plus 3 GPU’s and their powered Risers and the other PSU to the other 4 GPU’s and their powered risers?
